SCUBAPRO-UWATEC ALADIN SPORT Technical Information download pdf (Page 40)

IX Appendix

XI UWATEC

Smart dive computers

1 Technical information

Operating altitude: with decompression information: sea level up to approx. 4000 m (13120ft);

w/o decompression, w/o RBT information: usable in gauge mode (at any altitude)

Max. displayed depth: 120m (394 ft), resolution between 0.8 m and 99.9 m: 0.1 m, >99.9 m: 1m

The resolution in feet is always 1 foot

• Do not dive deeper than the limits given by the chosen fraction of oxygen

(decompression sickness, oxygen toxicity).

• Never dive deeper than your training qualification (experience) allows you.

• Always observe local dive depth restrictions.

Decompression calculation depth range: 0.8 to 120m (3 to 394 ft)

Maximum environment pressure: 13 bar (189 psi)

Clock: Quartz timer, display up to 999 minutes.

O2% Mix: Adjustable between 21%O2 (compressed air) and 100% O2

Operating temperature:

-10° to +50°C (14°F to 122°F).

Power supply: Special battery UWATEC LR07

Life of the battery: 500 to 800 dives, depending on the quantity of dives per year and the use of

the backlight.

Transmitter: High pressure connection: Maximum working pressure: 300 bar (4350 psi)

Life of the battery: up to 1000 dives, max. 3 years without use.

Power supply: User replaceable battery CR2450

2 Maintenance

The tank pressure gauge and the parts of this product used to measure the tank pressure should be serviced

by an authorized SCUBAPRO UWATEC dealer every second year or after 200 dives (whichever comes first).

Aside from that your TEC is virtually maintenance free. All you need to do is to rinse it carefully with fresh

water after each use and to have the batteries changed when needed. To avoid possible problems with your

TEC, the following recommendations will help assure that it will give you years of trouble free service:

• Avoid dropping or jarring your TEC.

• Do not allow your TEC to be exposed to direct, intense sunlight.

• Rinse your TEC thoroughly with fresh water after each dive.

• Do not store your TEC in a sealed container; make sure there is free ventilation.

• If there are problems with operating the contacts, use soapy water to clean

TEC and dry it thoroughly. The surface of your TEC housing can be treated

with

silicone grease. Do not apply grease to the water contacts!

• Do not clean TEC with liquids containing solvent (apart from water).

• If the service icon appears, TEC must not be used for any further dives. Take

your dive computer to an authorized SCUBAPRO UWATEC dealer.

Take the dive computer to an authorised SCUBAPRO UWATEC dealer in order

to change the batteries. The battery replacement is carried out by a SCUBA-

PRO UWATEC

subsidiary. TEC is checked for its technical integrity

at the same

time. Do not attempt to have the batteries changed by anyone other than an

authorised SCUBAPRO UWATEC dealer.

2.1 Replacing the battery of the transmitter

It is recommended to have the battery of the transmitter replaced by an

authorized

SCUBAPRO UWATEC dealer. The change must be made with par-

ticular care in order to prevent water from seeping in.

The warranty does not cover damages due to an improper replacement of the

battery.

Transmitter battery set (PN 06.201.920): Includes a Type CR 2450 battery and a 26.00 x 2.00 mm trans-

mitter cap o-ring .

WARNING

1 2 ... 35 36 37 38 39 40 41 42 43 44

Comments to this Manuals

No comments

SCUBAPRO-UWATEC ALADIN SPORT Technical Information Page 40

Comments to this Manuals

Related products and manuals for Scuba diving fins SCUBAPRO-UWATEC ALADIN SPORT